收藏本站
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
DEADTIME COMMAND
Deadtime prevents the turn-on of both transistors in the
same phase until the deadtime has expired. The deadtime
timer starts when a FET is commanded off (see Figure 6 and
Figure 13 ). The deadtime control is disabled by enabling the
FULLON mode.
The deadtime is set by sending the DEADTIME command
(100x xxx1), and then sending a calibration pulse of CS. This
pulse must be 16 times longer than the required deadtime
(see Figure 19 ). Deadtime is measured in cycle times of the
internal time base, f TB . This measurement is divided by 16
and stored in an internal register to provide the reference for
timing the deadtime between high and low gate transactions
in the same phase.
For example: the internal time base is running at 20 MHz
and a 1.5 μs deadtime is required. First a DEADTIME
command is sent (using the SPI), then a CS is sent. The CS
pulse is 16*1.5 = 24 μs wide. The IC measures this pulse as
24000 ns/50 ns = 480 clock cycles and stores 480/16 = 30 in
Table 13. .DEADTIME Command
the deadtime register. Until the next deadtime calibration is
performed, 30 clock cycles will separate the turn off and turn
on gate signals in the same phase. The worst case error
immediately after calibration will be +0/-1 time base cycle, for
this example +0 ns/-50 ns. Note that if the internal time base
drifts, the effect on dead time will scale directly.
Sending a ZERO DEADTIME command (100x xxx0) sets
the deadtime timer to 0. However, simultaneous turn-on of
High Side and Low Side FETs in the same phase is still
prevented unless the FULLON command has been
transmitted. There is no calibration pulse expected after
receiving the ZERO DEADTIME command.
After RESET, deadtime is set to the maximum value of 255
time base cycles (typically 15 μs).
The IC ignores any SPI data that is sent during the
calibration pulse. If there are any transitions on SI or SCLK
while the Deadtime CS pulse is low, a Framing Error will be
generated, however, the CS pulse will be used to calibrate
the deadtime
SPI Data Bits
Write
7
1
6
0
5
0
4
x
3
x
2
x
1
x
0
ZERO/
CALIBRATE
Reset
x
x
x
x
CS
SCLK
SI
CS
SCLK
SI
Deadtime
DEADTIME
Command
Deadtime Calibration Pulse Pulse
SO
SO
Figure 19. Deadtime Calibration
33937A
Analog Integrated Circuit Device Data
34
Freescale Semiconductor
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MDN2BL3GRAS MOTOR BRUSHED DC 2V 2753RPM
MDN3BL3CSAS MOTOR BRUSHED DC 2V 1458RPM
MIC2287-34YML TR IC LED DRIVER WHITE BCKLGT 8-MLF
MIC2289C-34YD6 TR IC LED DRIVR WHITE BCKLGT TSOT-6
MIC2291YD5 TR IC LED DRIVER PHOTO FLASH TSOT-5
MIC2293-15YML TR IC LED DRIVER WHITE BCKLGT 8-MLF
MIC2293C-34YML TR IC LED DRIVER WHITE BCKLGT 8-MLF
MIC2297-42YML TR IC LED DRIVR WHITE BCKLGT 10-MLF
相关代理商/技术参数
MCZ33970EG 功能描述:马达/运动/点火控制器和驱动器 DUAL GAGE DRVR IMP DAMP RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MCZ33970EG 制造商:Freescale Semiconductor 功能描述:IC STEPPER MOTOR GAUGE DRIVER SPI
MCZ33970EGR2 功能描述:马达/运动/点火控制器和驱动器 DUAL GAGE DRVR IMP DAMP RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MCZ33972AEK 功能描述:接口 - 专用 MULT SW DET SUP-WKUP RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59
MCZ33972AEK/R2 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Multiple Switch Detection Interface with Suppressed Wake-up
MCZ33972AEKR2 功能描述:接口 - 专用 MULT SW DET SUP-WKUP RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59
MCZ33972AEW 功能描述:接口 - 专用 MULT SW DET SUPRESS WU RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59
MCZ33972AEW/R2 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Multiple Switch Detection Interface with Suppressed Wake-up